Zhangjiagang Asino Sealing Tech Co.,Ltd215600About UsNO.,888 Jingang Avenue , Economic Development Zone, Zhangjiagang, Zhangjiagang City, Jiangsu.Zhangjiagang Asino SealingTech Co., Ltd. was established in 2012 and is committed to providing fluid sealing products for all kinds of rotating equipment (mainly including compressors, pumps and kettles). The main business is the research and development, design, Production and sales of mechanical seals and sealing products, while providing customers with technical consulting, technical training, online monitoring, fault diagnosis and other technical services covering the entire life cycle of the product.Zhangjiagang Asino Sealing Tech Co.,Ltd215600About UsNO.,888 Jingang Avenue , Economic Development Zone, Zhangjiagang, Zhangjiagang City, Jiangsu.Zhangjiagang Asino SealingTech Co., Ltd. was established in 2012 and is committed to providing fluid sealing products for all kinds of rotating equipment (mainly including compressors, pumps and kettles). The main business is the research and development, design, Production and sales of mechanical seals and sealing products, while providing customers with technical consulting, technical training, online monitoring, fault diagnosis and other technical services covering the entire life cycle of the product.Zhangjiagang Asino Sealing Tech Co.,LtdZhangjiagang Asino Sealing Tech Co.,LtdZhangjiagang As
The AS-CFI cartridge mechanical seal is to replace AES-BDFI (Bellows Double Flow Induction )type.
Features: 1.Incorporates pumping ring to maximize cooling and increase seal life 2.large 3/8"ports maximize cooling and extend seal life 3.Integral deflector guides cooling barrier fluid to the most essential areas 4.Sizes available from 1.000"to 5.000"(24mm - 125mm) in standard and ANSI Plus gland formats
Background Knowledge:
An important indicator of O-ring design——initial compression rate
Initial compression rate mainly refers to the compression rate of O-ring seal when it is installed in the groove.This indicator mainly reflects possible installation problems caused by manufacturing tolerances of O-ring seals.Also initial compression rate changes will cause changes in working compression rate.
If initial compression rate is too large, sealing ring for the hole will be twisted in the groove. Thus，state of sealing ring will be unstable during floating process of the compensation ring, and there is a hidden danger of mechanical seal failure.
Initial compression rate will also affect performance of shaft sealing ring. If too large, shaft sealing ring will be overstretched, cross-sectional diameter of sealing ring will be reduced, working compression rate will not meet design requirements, and the mechanical seal will fail;if too small, sealing ring will fail to be loaded into the groove. Therefore, design principle of initial compression rate is: maximum value of inner diameter of the sealing ring is equal to minimum value of bottom diameter of groove on the shaft.
AS-CFI to replace AES-BDFI cartridge mechanical seal
AS-CFI
0.00~0.00
The AS-CFI cartridge mechanical seal is to replace AES-BDFI (Bellows Double Flow Induction )type.
Features: 1.Incorporates pumping ring to maximize cooling and increase seal life 2.large 3/8" ports maximize cooling and extend seal life 3.Integral deflector guides cooling barrier fluid to the most essential areas 4.Sizes available from 1.000" to 5.000" (24mm - 125mm) in standard and ANSI Plus gland formats
AS-CFI to replace AES-BDFI cartridge mechanical seal
AS-CFI
0.00~0.00
The AS-CFI cartridge mechanical seal is to replace AES-BDFI (Bellows Double Flow Induction )type.
Features: 1.Incorporates pumping ring to maximize cooling and increase seal life 2.large 3/8" ports maximize cooling and extend seal life 3.Integral deflector guides cooling barrier fluid to the most essential areas 4.Sizes available from 1.000" to 5.000" (24mm - 125mm) in standard and ANSI Plus gland formats
Español
Pусский
